Technics® 1200/1210 series
'PlugNPlay' LED Kits Installation Guide
|
Technics® 1200/1210 series 'PlugNPlay' LED Kits Installation Guide |
|
| 33/45 & Pitch Slider Guide | PopUp Guide |
Terms of Use and Disclaimer |
| The information contained
herein is provided for the sole purpose of illustration of
part replacement. And should be used at your own descretion as a guide only.
Although the kits have been made
for the lay-person to self install. As with any electrical
appliance, any warranty may be voided and should be performed by an
authorized service center for the respective device. As indicated by the
original equipment manufacturer's labeled warning. By no means shall the manufacturer Technology Transplant® or it's resellers be held responsible for any damages or injury that may occur from it's installation or use of the guide. By use of this guide the user assumes full responsibility of person and equipment. As with any electrical appliance. Use good judgment of your own capabilities as to whether this product or guide is right for you. © 2010 Technology Transplant. |
|
PopUp Guide |
|
|
IMPORTANT 
Do no service with unit powered!
PopUp LED kits come with a special PCB provided. Do not attempt to attach new PopUp LED to original switch installed to bypass work.
The original switch with resistor is not configured for an LED! The PopUp LED will blow out!
If not done during initial disassembly. Remove the connector for the Pop Up Lamp "DP122 LAMP".
Below shows the removal of the two screws and tape harness that holds the lamp assembly in place.
'
Popup lamp assembly removed.
Cut the leads of the Orange and Brown wires as shown. Then unscrew the switch assembly.
Once the wires have been cut you may easily pull the old lamp out of the metal assembly as shown below.
To feed the wiring through the
assembly. Gently bend the cables 2 contact leads to an angle as
shown (left).
This will allow the new popup
wires to be easily fed down into the housing and exit out the bottom hole (right).
Push down from the top of the PopUp LED to move it down the assembly. The 2 contact leads should only barely visibly be protruding from the exit.
Push down the entire metal holder until you can see when the wire are protruding, gently begin to pull them out the exit hole.
Grip onto the black heat-shrinked area not the wiring or headers when pulling the lamp into place .
It is useful to use the small screw driver
provided with your kit to maneuvre the spring.
Wedge and and pull down the
internal spring by pulling the screwdriver in towards you. This is to allow the new PopUp LEDs wire to easily exit on install.
Before attaching the new PopUp PCB. The opposite side (inner-side) has glue residue you should scrape off that may be covering the 2 screw holes.
The socket and 3 silver screws provided with your kit should go to the areas shown.
The smallest screw attaches the PopUp Lamp cover. The two longer screws
are for the PCB to affix to the assembly.
Test the movement of the mechanism. If in replacement some of the grease has come off and it doesn't 'slide' smoothly.
You can use a lubricant such as petroleum jelly and a cotton swab to apply to areas to re-grease.
Attach the socket header as shown
to the appropriate colors. The socket should LOCK the cable in
place.
If the cable is not locking
you have it reversed and turn it the direction to fit into the header properly
so that it locks in place.
The unit completely assembled. Note orientation of the colors of the socket and wire are correct.
Before putting on the aluminum top, be sure to adjust LED PCB as shown.
Feed the new cable back
underneath the main board to the other side and attach to Pop Up Lamp (DP122) label side up.
You can then safely test the lamp before fully re-assembling the
turntable to test.
|
Technics® 1200/1210 series 'PlugNPlay' LED Kits Installation Guide |
|
| 33/45 & Pitch Slider Guide | PopUp Guide |
Terms of Use and Disclaimer |
| The information contained
herein is provided for the sole purpose of illustration of
part replacement. And should be used at your own descretion as a guide only.
Although the kits have been made
for the lay-person to self install. As with any electrical
appliance, any warranty may be voided and should be performed by an
authorized service center for the respective device. As indicated by the
original equipment manufacturer's labeled warning. By no means shall the manufacturer Technology Transplant® or it's resellers be held responsible for any damages or injury that may occur from it's installation or use of the guide. By use of this guide the user assumes full responsibility of person and equipment. As with any electrical appliance. Use good judgment of your own capabilities as to whether this product or guide is right for you. © 2010 Technology Transplant. |